Temperature controls for kilns
Temperature controls
Art. No.: 73010
- Connected load: 230 V~, 16 A
- Ohmic load: up to 3.500 W
By connecting this device upstream, you can achieve any approximately constant firing temperature in any Abig-Uhlig kiln, making it possible to fire glass and ceramic paintings. The temperature controller is highly recommended for all kilns, as it allows you to take full advantage of the many possibilities offered by Abig devices and significantly increases the service life of the heating coils.
Suitable for:
- ABIG 110 (KF)
- ABIG 135 (KF)
- ABIG 150 (KF)
- ABIG 180 (KF)
- ABIG 180 L (KF)
- Uhlig U5
- Uhlig U15
- Uhlig U24
- Uhlig U92
Temperature regulator TRP008
Art. No.: 73020
- Maximum temperature: 1.200° C
- Thermal element: NiCr-Ni sensor (included)
- Switching capacity: 230 V, 50/60 Hz, 3.500 W
Description:
The TRP 008 control unit is an automatic two-point controller with digital actual value and setpoint display. A NiCr-Ni thermocouple in accordance with DIN 43 710 (included with the device) serves as the measuring sensor.
The TRP 008 control unit is used specifically for temperature control in enamel, melting, annealing, and tempering furnaces, as well as for firing decorative images, etc. The controller is used wherever a constant temperature is required for any length of time without a heating ramp.
The thermocouple is inserted into the measuring opening at the rear of the kiln, and the kiln is plugged into the controller’s socket and switched on by the controller up to a power of 3.500 Wat 230 V ohmic load).
Suitable for:
- ABIG 110 (KF)
- ABIG 135 (KF)
- ABIG 150 (KF)
- ABIG 180 (KF)
- ABIG 180 L (KF)
- Uhlig U5
- Uhlig U15
- Uhlig U24
- Uhlig U92
Temperature regulator TRP010
Art. No.: 73030
- Maximum temperature: 1.200° C
- Thermal element: NiCr-Ni sensor (included)
- Switching capacity: 230 V, 50/60 Hz / 3.500 W
- Ramps: 3 (Heating rate, target temperature, hold)
Description:
The TRP 010 control unit is a program controller with digital actual value and setpoint display. A thermocouple in accordance with DIN 43 710 (included with the device) serves as the measuring sensor. The TRP 010 control unit is used specifically for temperature control in enameling, melting, annealing, and tempering furnaces, as well as for firing ceramics, porcelain, etc. The controller is used wherever a temperature is required over three stages (heating up, full load, holding).
The thermocouple is inserted into the measuring opening at the rear of the kiln, and the kiln is plugged into the controller’s socket and switched on by the controller up to a power of 3.500 W at 230 V (ohmic load).
Suitable for:
- ABIG 110 (KF)
- ABIG 135 (KF)
- ABIG 150 (KF)
- ABIG 180 (KF)
- ABIG 180 L (KF)
- Uhlig U5
- Uhlig U15
- Uhlig U24
- Uhlig U92
Temperature measuring device
Art. No.: 73100
- Temperature measuring device with temperature sensor.
- Firing kilns with 8 mm sensor hole.
- Measuring range from 20° – 1.200° C
Description:
The temperature measuring device displays the current temperature of the kiln digitally. A thermocouple in accordance with DIN 43 710 (included with the device) serves as the measuring sensor. The thermocouple is inserted into the measuring opening on the rear of the kiln.
It is essential to observe the maximum temperature of your kiln.
Suitable for:
- ABIG 110 (KF)
- ABIG 135 (KF)
- ABIG 150 (KF)
- ABIG 180 (KF)
- ABIG 180 L (KF)
